INDOOR SINGLE PASSIVE INFRARED DETECTOR
DS-360 is a completely of new product of single passive infrared detector which can provide high quality and safety of indoor ,When it detects the invasion of illegal area,it will notify the user timely .
ceiling mounted PIR sensor it Adopt advanced and stable circuit design, very low rate of failure alarm and false alarm; it can realize complete movement detection and actually temperature compensation. it can reduce its false alarm greatly during hot air current, moving animals and great changes in temperatures. Its PIR detection than other normal PIR detectors in the market.
The product is ceiling passive infrared detector with high stability. It adopts advanced signal processing technology, providing superhigh detection and anti-false alarm abilities. When an intruder passes through the detection area, the detector will detect the movements of human body automatically. If any movements, it will send alarm signal to the connected alarm host. It is suitable for safety protection in residential house, villas, factories, shopping malls, warehouses and office buildings etc.
It has the following characteristics:
- Anti-pet function
- Anti white light interference
- Selectable detection sensitivity
- Strong anti-interference ability , high anti-false alarm
- Anti-glare protection
- Intelligent temperature compensation,it can work stably even in high temperature conditions
- High density detection area
- Anti-tamper switch protection
- Using microprocessor chip design,with advanced motion analysis
- Wall/ceiling installation
| MODEL | DS-360 |
| Detection Range | Coverage10m diameter (Mounting height 3m) |
| Input Voltage | 10〜16V DC |
| Operating Current | 20mA(max.) |
| Sensitivity | 2°C(0. 6m/sec) |
| Warm-up Period | 35±5sec |
| Alarm Period | 2.0±0.5sec |
| LED Indicator | Red Alarm LED(Selectable On/Off) |
| Alarm Output | N.C., 20V DC 100mA max. |
| Tamper Output | N.C.,Open when cover is removed. 30V DC,0.5A max. |
| Mounting Height | 7.8 〜11.8ft (2.4〜3.6m) |
| Operating Temp. | 14°F ~ 131°F (-10C~55C) |
| Environmen Hum | 95% max. |
| Weight | 3.7 oz (105g) |
| Dimensions | 4.72"DIA.x1.61" H (120mmDIA.x41mm H) |
2. DESCRIPTION AND OPERATION
3. INSTALLATION HINTS
4. DETECTION PATTERN
5. INSTALLATION
6. WIRING
7. TROUBLE SHOOTING AND MAINTENANCE
| TROUBLE | TROUBLE CAUSE | REMEDY |
| Unit does not power up. | No or low input power. | Apply proper input voltage. |
| Input power polarity reversed. | Correct wiring polarity. |
| Alarm LED does not light | LED jumper is set to “LED OFF”. | Set LED jumper to “LED ENABLE”(See Section 2). |
| Incorrect sensor mounting height. | Increase /decrease mounting height. |
| Alarm LED/Relay triggers without movement in detection area. | Unsecured environment:Animals / rodents in detection area . | Block access of animals / rodents. |
| Heater/air conditioning equipment in sensor view. | Re-aim sensor. |
| Direct sun or headlights in sensor view. | Add curtain / shade to block light sources. |
| LED indicates alarm, no alarm output. | Incorrect wiring at alarm output terminals. | Correct wiring fault. |
| Lightning damage. | Replace sensor. |
| Alarm LED on constantly, no fault in protected area or wiring. | Defective unit. | Replace sensor. |
| Unit continues to operate after the input power has been disc-onnected. | The wire to the “ - ” power input was disconnected, the“ + ” is still connected. the power can now find a return path through the Alarm Output protection device and alarm wiring. | Disconnect wire from the “ + “ power input. |
8. NOTES
1.The product shall be installed indoor and do not use it under the following conditions.
① In the place where it is likely to be exposed to dust, high humidity,high temperatures,or rain.
② In the place where it is closed to magnetic field.
③ In the place where vibration or shock is directly transmitted to the product.
2.In order to ensure the normal operation of the product. It should be cleaned and maintained
regularly.
① Please power off before cleaning the product.
② Do not use chemical detergents to clean the product.
3.Never disassemble, repair and modify the product.
4.The product comply with the SJ/T11363-2006 Standard and requirements of RoHS.
5. Specifications and design are subject to change without prior notice.
